Bill Battocchio


This Lipped Bowl was turned from Juniper and finished by buffing.
5/5/2017 Click on image to see closeup.


A pancake flipper obtained from Goodwill and with a new handle made of Teak and finished in Polyurethane.
5/5/2017 Click on image to see closeup.



11/3/2016 Click on image to see closeup.


Vase for the Silent Auction
8/12/2016 Click on image to see closeup.


Bill turned these two bowls from natural bark Avocado. The wood was wet when turned. The finish is buffing.
5/9/2016 Click on image to see closeup.


Two turned bowls made from local Olive. The finish is buffed lacquer.
3/4/2016 Click on image to see closeup.


A special push stick to cut the lids of the heart boxes.
3/4/2016 Click on image to see closeup.


Bill made these cutting boards from Oak, Maple, Walnut, and Purple Heart. They are finished Mineral Oil.
9/4/2015 Click on image to see closeup.


Bill's contribution to the auction was this bowl of Camphor and a Bubinga finial.
8/8/2015 Click on image to see closeup.


Bill turned this bowl from Olive. It is finished with Sam Moolof Oil and buffed. He was careful to dry the wood between steps so there are no cracks.
3/6/2015 Click on image to see closeup.


The first is a Bowl made from wet Plum. The finish is a home-made mixture. The second is a Lidded Bowl made from Olive and finished in Lacquer.
6/6/2014 Click on image to see closeup.


Letter Opener made from scrap wood.
5/7/2014 Click on image to see closeup.


For the challenge, Bill made this Jewelry from assorted wood and finished them in wax.
1/10/2014 Click on image to see closeup.


Bill make this Future Car for the toy challenge from Walnut and Maple. The finish is Polyurethane. Bill says it looks like a Prius.
9/6/2013 Click on image to see closeup.


Fish Puzzle (four of them) made from plywood.
1/11/2013 Click on image to see closeup.


Bill made this cutting board for the July Challenge.
7/6/2012 Click on image to see closeup.


Bill turned this Goblet with Captured Ring from Olive and finished it with Polyurethane and wax.
5/4/2012 Click on image to see closeup.


Bill is doing the Toy Car for the toy project. The woods are Zircote, Walnut, ALder, Maple, Red Cedar, Baltic Birch Plywood, Fir and an unknown wood. The finish is Polyurethane. Approximate time of manufacture is 5 hours.
8/24/2011 Click on image to see closeup.


Salt & Pepper Shakers, Wine Goblet, and Ice Cream Scoop by Bill. The woods are Stinkwood and Alder. The finish: Polyurethane.
7/9/2011 Click on image to see closeup.


Bill made this Small Vessel from Camphor wood. It was done in conjunction with Camarillo House.
6/4/2011 Click on image to see closeup.


Bill made this Model Airplane from Arlen Wood.
7/4/2009 Click on image to see closeup.


Bill turned this World Clock from Walnut Arlen Wood.
7/4/2009 Click on image to see closeup.


Bill made this Scraper for the tool challenge. The handle is Walnut and finished with wax. All parts were taken from scrap.
1/9/2009 Click on image to see closeup.


This Craftsman Clock is made from Walnut, Oak, Pine, Poplar, Maple, Redwood, Cedar, Mrytlewood. The finish is Polyurethane.
8/8/2008 Click on image to see closeup.


This Sports Clock is a wall hanging made from Bass, Cedar, Pine, Walnut, Alder and Purple Heart. The finish is Lacquer.
9/8/2006 Click on image for closeup.